Receiving Inspector
Everett, WA
Full Time
Aerospace
Experienced
General Summary
Under general supervision and reporting to Quality Management in Quality Operations, The Receiving Inspector, (RI) is responsible for performing receiving inspection operations of all incoming product, hardware, and all COTS items. RI shall consist of but not limited to reviewing all incoming paperwork including raw material certifications, other certifications including testing and metallurgical data. Any outside processor certifications, and general dimensional and visual inspection. The RI may include reviewing all paperwork relating to the product at hand. The RI will also verify FAI’s to AS9102 for accuracy and completeness. The RI must be familiar with hand tools and gaging techniques. The RI will also be fluent in B/P interpretation and GD&T.
Essential Job Functions
Knowledge of:
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this position. Reasonable accommodations may be made to enable individuals with disabilities to perform the functions. While performing the duties of this position, the employee is regularly required to talk or hear.
WORKING CONDITIONS
Productivity: Incumbents must perform work in an efficient, effective, and timely manner with minimal direction.
Mobility: Incumbents are required to participate in assigned physical activities which may include light lifting and sitting for prolonged periods of time.
Vision: Vision sufficient to read printed documents, computer screens, and observe behavior of others.
Environment: Typical office conditions, directly working Quality management team, working with the SMS team, and external customers.
Other Factors: Incumbents may be required to work occasional extended hours and weekend overtime.
The employee frequently is required to use hands or finger, handle, or feel objects, tools, or controls. The employee is occasionally required to stand; walk (approximately 1-2 miles a day); sit; reach with hands and arms; climb or balance; and stoop, kneel, crouch, or crawl. Employee will occasionally drive long distances to and from various suppliers as needed. The employee must occasionally lift and/or move up to 20 pounds. Specific vision abilities required by this position include close vision, distance vision, color vision, peripheral vision, and the ability to adjust focus. The noise level in the work environment is usually moderate to high.
Pay Range: $25 - $40 hourly Please note that the salary information is a general guideline only. TRIGO ADR Americas considers factors such as (but not limited to) scope and responsibilities of the position, candidate’s work experience, education/training, key skills, internal peer equity, as well as, market and business considerations when extending an offer.
Under general supervision and reporting to Quality Management in Quality Operations, The Receiving Inspector, (RI) is responsible for performing receiving inspection operations of all incoming product, hardware, and all COTS items. RI shall consist of but not limited to reviewing all incoming paperwork including raw material certifications, other certifications including testing and metallurgical data. Any outside processor certifications, and general dimensional and visual inspection. The RI may include reviewing all paperwork relating to the product at hand. The RI will also verify FAI’s to AS9102 for accuracy and completeness. The RI must be familiar with hand tools and gaging techniques. The RI will also be fluent in B/P interpretation and GD&T.
Essential Job Functions
- PCB, PCBA Hardware Experience required
- Experienced quality individual in dimensional and visual inspection of aerospace machined components
- Experience in reading and interpreting FAI’s – AS9102
- Experience with hand measurement tools
- Knowledge and experience in GD&T (ASME Y14.5)
- Knowledge and experience with blueprint interpretation
- Perform receiving inspection and read and interpret material certs.
- Basic knowledge of Excel required
Knowledge of:
- Experienced quality individual in dimensional and visual inspection of aerospace machined components and assemblies
- Experience in reading and interpreting FAI’s – AS9102
- Experience with hand measurement tools
- Knowledge of CMM Inspection process (Knowledge of CMM Programming is not required)
- Knowledge and experience in GD&T (ASME Y14.5)
- Knowledge and experience with blueprint interpretation
- MS Outlook, and EXCEL experience
- Strong verbal, written and communication skills
- Fluent English – reading and writing is required
- Professionalism, integrity, and exceptional attention to detail
- Strong independent decision-making skills; excellent analytical skills and professional judgment
- Excellent interpersonal, written, and verbal communication skills
- Knowledge of basic computer skills, include basic Excel skills
- IPC610 and J-STD/Space Addendum Preferred
- Work as an effective team member
- Establish and maintain effective working relationships
- Fluent English – reading and writing is required
- Pass pre-hire background check including DMV and credit screening
- Pass Pre-hire Drug Screening
- The work is performed under general supervision
- None
- High School Diploma or AA/AS degree or other 2-year post high school training with a minimum of 3+ years relevant experience
- 3+ years’ experience as a quality inspector
- 3+ years’ experience in inspection duties, FAI’s GD&T, and b/p interpretation
- Proficient with Microsoft Outlook and Excel
- Effective communication skills
- Detail oriented
- Any combination of education and experience may be considered
- Experience with hand gages and measuring equipment
- Experience in an aerospace manufacturing facility
- The General Vision Acuity Test shall be performed by an Oculist, Optometrist, or other professionally recognized person. The following requirements shall apply.
- Near Vision – Eyes meets Ortho rater 8 (95% or Jaeger #2 at 12 inches)
- Far vision – Eyes meets Ortho rater 4 (76%) or Snellen Chart 20/50
- Color Perception – 6 of 9 Ortho rater plates US or International citizenship or permanent residence status required depending on work location.
- Valid Driver’s License
- Valid Auto Insurance
The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this position. Reasonable accommodations may be made to enable individuals with disabilities to perform the functions. While performing the duties of this position, the employee is regularly required to talk or hear.
WORKING CONDITIONS
Productivity: Incumbents must perform work in an efficient, effective, and timely manner with minimal direction.
Mobility: Incumbents are required to participate in assigned physical activities which may include light lifting and sitting for prolonged periods of time.
Vision: Vision sufficient to read printed documents, computer screens, and observe behavior of others.
Environment: Typical office conditions, directly working Quality management team, working with the SMS team, and external customers.
Other Factors: Incumbents may be required to work occasional extended hours and weekend overtime.
The employee frequently is required to use hands or finger, handle, or feel objects, tools, or controls. The employee is occasionally required to stand; walk (approximately 1-2 miles a day); sit; reach with hands and arms; climb or balance; and stoop, kneel, crouch, or crawl. Employee will occasionally drive long distances to and from various suppliers as needed. The employee must occasionally lift and/or move up to 20 pounds. Specific vision abilities required by this position include close vision, distance vision, color vision, peripheral vision, and the ability to adjust focus. The noise level in the work environment is usually moderate to high.
BENEFITS:
- 12 days paid vacation first year, increasing with service years
- 10 days paid sick time
- 11 paid holidays
- Healthcare insurance available: Medical, dental, vision, STD, LTD, critical illness, life insurance for self and dependents
- Champ Plan Wellness and Health
- Free to employees working minimum 20 hours/week with anticipated $30k/annual earnings
- Participation increases net take home pay $$$ in most instances
- Free wellness initiatives
- Free tele-health
- Free and discounted RX
- Auto enrollment (unless tax elections result in negative impact)
- Eligible on the 1st of the month following 30 days of continuous employment
- requires monthly 10-minute wellness activity participation
- 401k retirement savings with match
- Eligible on the first (1st) of the month following 90 days of continuous employment
- 100% match of 1st 3% contribution
- 50% match of next 2% contribution
- IMMEDIATE VESTING
- Company-provided cell phone, laptop, mobile wi-fi (for business use only)
- Regular Hourly rate for travel time
- Direct Pay Travel arrangements for flights, hotels and rental cars
- Travel Reimbursements direct deposited with each payroll
- Federal rate Mileage reimbursement (.70/mile 2025) when driving personal vehicles on company business
- Per diem reimbursements for meals and incidentals
- Overnight trips - Up to $75
- Leaving home after 4 pm $40
- Federal rate mileage reimbursement (.70/mile 2025) when driving personal vehicles on company business
- Direct Pay Travel arrangements for flights, hotels and rental cars
- Travel Reimbursements direct deposited with each payroll
- Per diem reimbursements for meals and incidentals
- Overnight trips - Up to $75
- Leaving home after 4 pm $40
- $1500 EMPLOYEE REFERRAL BONUS
- Initial $750 paid upon hire of qualified referred employee (rehires excluded)
- Additional $750 paid upon referral’s full completion of 90 days’ employment
Pay Range: $25 - $40 hourly Please note that the salary information is a general guideline only. TRIGO ADR Americas considers factors such as (but not limited to) scope and responsibilities of the position, candidate’s work experience, education/training, key skills, internal peer equity, as well as, market and business considerations when extending an offer.
Company Overview
TRIGO ADR Americas is the leader in the Aerospace & Defense Industry providing global Supplier Delivery Assurance, Supplier Development and Quality Management Services. Trigo provides a fully integrated service solution to optimize Supplier performance through an embedded “boots on the ground” business model to drive systemic changes that enhance Supplier Quality and Supplier Delivery performance. We work as an extension of our customers to build and maintain supplier and customer collaboration to ensure improved results and provide visibility throughout the supply chain. Trigo’s team of dedicated Delivery Assurance Specialists, Supplier Development Specialists, Supplier Quality Engineers and Program Managers support hundreds of Customers and are deployed to thousands of Suppliers worldwide focused on achieving On-Time and On-Quality Delivery results.
TRIGO ADR Americas is an Equal Opportunity Employer, including disabled and veterans, and may require US Citizenship for employment on certain defense contracts subject to ITAR restrictions. All qualified candidates will receive consideration. Except where otherwise provided by law, selection will be made without regard to, and there will be no discrimination because of race, religion, color, national origin, sex, political affiliations, marital status, non-disqualifying physical or mental disability, age, sexual orientation, gender identity, genetic information, membership or non-membership in an employee organization, or on the basis of personal favoritism or other non-merit factors.
Apply for this position
Required*